The airflow milling work is that compressed air is frozen, filtered, dried, and several nozzle spraying through two-dimensional or three-dimensional arrangement forms an ultrasonic speed gas flow into the pulverizing chamber, and the gas flow impact can make the material are fluidized. , The accelerated material is combined in several nozzles, which produces severe collision, friction, and shear, and ultrafine pulverization of the particles.
Metal silicon is also known as crystalline silicon or industrial silicon, which mainly uses an additive as a non-ferrous alloy. The airflow pulverizer is generally used for ultrafine pulverization grading of metal silicon, which has the characteristics of fine particle size, narrow particle size distribution, and good dispersibility. When the metal silicon gas flow pulverizer is in use, it needs to be operated in accordance with the correct method to avoid the occurrence of equipment failure or safety accidents due to improper operation. The following is a premature item of the use of metal silicon gas flow crushers by Xiaobian.
1, the operator should read this instruction manual, familiar with the performance, structure, and use of this machine, and install debugging, use and maintenance according to the provisions of this specification.2, must be strictly selected by the spindle speed of the spindle speed of various models, warning: It is strictly forbidden to improve the speed of the spindle.
3, the crushed material should remove hard objects such as mixed wires and stones. Note: The feeding machine should be prevented, otherwise damage to the sieve, hammer and other parts.
4, when the operator feeds, it should stand on the side of the feeding port, warning: It is forbidden to use iron bars, wooden rods, and do not allow the hand to extend into the warning line of the feeding port, sometimes the material is large The material can be pushed into the crushing chamber of the mill with a harder crop straw.
5, when working, pay attention to the bearing temperature cannot exceed 55 ° C, if there is overheating phenomenon, stop checking immediately, so as not to burn bad bearings, spindles, etc.
6, should clean up the materials in the assembly bag in time, otherwise it will affect the production efficiency.
7. Adjusting the chassis, hammers or triangle, should open the blockage of the casing to clean the crushing room, pay attention: The power must be disconnected to ensure safety.
8. When the open-air homework is completed, it must be cleaned up within the machine group, and the components such as anti-screening should be rusty and must be waterproof.
9. The people who are less than 16 years of age and more than 55 years old and those who don't understand the operation of this unit cannotSeparate jobs.
10, should avoid using a fake hammer, preventing the vibration caused by the imbalance of the rotor damage to the machine's service life, in order to extend the service life of the whole machine. Be sure to use the various parts produced by our factory.
11. If the airflow pulverizer is working, if there is a fault, the power is turned off, and after the machine stops running, it will be maintained, warned: When the machine is running, the body should be locked, it is strictly forbidden to open.
12. After the wine is strictly forbidden, the disease is ill, and the fatigue is working separately.
13. The machine should be equipped with a belt guard to prevent human safety.
14. When the airflow crusher checks whether the components are fastened, after the operation is completed, clean up and check, the machine works for 200 hours, and should check the wear of rotor, hammer, blade dish or blades, pay attention: If the pin, hammer or open portraits are found to be crack and abnormal wear, it should be replaced immediately to avoid serious damage to the machine and personal injury and death.
All large mechanical equipment including metal silicon flow pulverizer, must operate correctly and scientifically maintained during use. Under normal circumstances, the airflow pulverizer manufacturers will arrange professional training for users to conduct professional training for special sales engineers after selling equipment. Shandong El Pie as a domestic large airflow crusher manufacturer, with professional after-sales team, providing users with perfect after-sales service.
ALPA provides customers with installation guidance services, after the equipment enters the field, the service engineer will go to the on-site guidance installation and provide system training for customer operators. During the practice of technicians, the training lecturers will continue to follow up the operational project to ensure that the project is organized, and the production line is stable and efficient.